8Pin Auxiliary Relay Connection | 220Vac Auxiliary Relay Hold Unhold With Push Button
After Dave's last video we've received a metric ton of comments asking about the method and techniques for de-pinning connectors. Not to leave you guys hanging we quickly gathered a whole bunch of the most commonly used aftermarket connectors, and threw them at Dave yelling: “Go on then, de-pin these, and look sexy while doing it!” As Dave always rose up to the challenge :)
This video will show you how to make a latching circuit or an on/off switch with a contactor or relay. With a latching circuit, the contacts will remain on once input power is applied and will remain on until the connection is broken. For this set up you will need a contactor, auxiliary contact, normally open pushbutton switch and a normally closed pushbutton switch. A relay can be used in place of a contactor as long as there is an auxiliary contact that will close when the coil is actuated.
With respect to the usage, installation or assembly of any products described in this video, Galco Industrial Electronics, Inc., a Michigan corporation, encourages you to follow the requirements and/or guidelines of: i) the Occupational Safety and Health Act of 1970 , Public Law 91-596, as amended, and all laws, rules and regulations implemented in relation thereto; ii) the National Electrical Code®; and iii) NFPA 70E®. Any installation, assembly or work described in this video should be performed by a qualified licensed electrician.
GTV, Galco, galco.com, Galco Industrial Electronics, and Galco Industrial Electronics, Inc. are registered and/or pending registered trademarks under the U.S. Patent and Trademark Office, assumed names, registered domain names, and/or trade names of Galco Industrial Electronics, Inc., a Michigan corporation.
LEGAL DISCLAIMER:
While we have made every attempt to ensure that the information provided is accurate and has been obtained from reliable sources, Galco is not responsible for any errors or omissions, or for the results obtained from the use of this information. All information is provided "as is", with no guarantee of completeness, accuracy, timelines or of the results obtained from the use of this information, and without warranty of any kind, express or implied, including, but not limited to warranties of performance , merchantability and fitness for a particular purpose. At all times you should defer to the instructions and safety guidelines issued by the manufacturer. In no event will Galco, its agents or employees thereof be liable to you or anyone else for any decision made or action taken in reliance on the information provided to you or for any consequential, special or similar damages, even if advised of the possibility of such damages.
8Pin Auxiliary Relay Connection | 220Vac Auxiliary Relay Hold Unhold With Push Button
After Dave's last video we've received a metric ton of comments asking about the method and techniques for de-pinning connectors. Not to leave you guys hanging we quickly gathered a whole bunch of the most commonly used aftermarket connectors, and threw them at Dave yelling: “Go on then, de-pin these, and look sexy while doing it!” As Dave always rose up to the challenge :)
This video will show you how to make a latching circuit or an on/off switch with a contactor or relay. With a latching circuit, the contacts will remain on once input power is applied and will remain on until the connection is broken. For this set up you will need a contactor, auxiliary contact, normally open pushbutton switch and a normally closed pushbutton switch. A relay can be used in place of a contactor as long as there is an auxiliary contact that will close when the coil is actuated.
With respect to the usage, installation or assembly of any products described in this video, Galco Industrial Electronics, Inc., a Michigan corporation, encourages you to follow the requirements and/or guidelines of: i) the Occupational Safety and Health Act of 1970 , Public Law 91-596, as amended, and all laws, rules and regulations implemented in relation thereto; ii) the National Electrical Code®; and iii) NFPA 70E®. Any installation, assembly or work described in this video should be performed by a qualified licensed electrician.
GTV, Galco, galco.com, Galco Industrial Electronics, and Galco Industrial Electronics, Inc. are registered and/or pending registered trademarks under the U.S. Patent and Trademark Office, assumed names, registered domain names, and/or trade names of Galco Industrial Electronics, Inc., a Michigan corporation.
LEGAL DISCLAIMER:
While we have made every attempt to ensure that the information provided is accurate and has been obtained from reliable sources, Galco is not responsible for any errors or omissions, or for the results obtained from the use of this information. All information is provided "as is", with no guarantee of completeness, accuracy, timelines or of the results obtained from the use of this information, and without warranty of any kind, express or implied, including, but not limited to warranties of performance , merchantability and fitness for a particular purpose. At all times you should defer to the instructions and safety guidelines issued by the manufacturer. In no event will Galco, its agents or employees thereof be liable to you or anyone else for any decision made or action taken in reliance on the information provided to you or for any consequential, special or similar damages, even if advised of the possibility of such damages.
No comments:
Post a Comment