How to make ups for WIFI router / 3s BMS module wiring diagram

The pandemic COVID-19 outbreak forced companies to continue with work-from-home policy to maintain social distancing and for business continuity. More and more of us are working from home these days, and that means your home's WiFi networks are more important than ever.

Anyone with a fixed-line connection will know that their WiFi drops whenever the power goes out. It is annoying if you are in an important meeting/webinar through Zoom, WebEx, or MS-Team, and there is an interruption due to power cuts.

Solutions:

1. Using a conventional UPS ( Bulky and Costly )

2. Mini-UPS (Light and Cheap)

I have already posted 3 Instructables ( V1, V2, and V4 ) on DIY Mini UPS, but this Instructables is the most advanced one which is designed by considering the feedback from the users of my earlier versions of UPS.

New Features are:

1. Automatic Switching (by using MOSFET) between the power supply and battery pack during the power failure

2. Two Output Ports: 12V /2A and 5V/2A or 9V/2A

3.More backup time (8hrs)

4. Battery pack with 3S BMS

5. Additional Protection

My Book: DIY Off-Grid Solar Power for Everyone

You can order my Book on Off-Grid Solar Power from Amazon

eBook

Paperback - Black & White

Paperback - Color Print

Support me On Patreon:

If you enjoy my work here on Instructables, consider joining my Patreon, it will be a great help for me to make more interesting projects in the future.

Condition-1: Mains Power Supply ON

In normal condition, power from the mains is drawn by a DC adapter through the input DC jack to charge the 6 x 18650 batteries and to provide power to the two output DC Jacks through the DC-DC converter modules. In this condition, the gate of the p-channel MOSFET (IRF9540) is high, so it will not conduct, and no power flow from the battery pack to the output. The direct power flow from the DC adapter to the battery pack is prevented by two Schottky diodes (1N5822).

Condition-2: Mains Power Supply OFF

When the mains power fails, the stored energy in the battery is used to power up the output DC jacks through the DC-DC converter modules. In this condition, the gate of the p-channel MOSFET (IRF9540) is grounded through the 10K resistor, so it will conduct, and power flow from the battery pack to the output.

Battery Pack and Charging Circuit:

In the schematic diagram, the 6 x18650 batteries are connected in 3S2P (3-series and 2 parallel) configuration and then they are connected to a 3S BMS board for protection during the charging and discharging. The battery pack is charged through the XL4015 buck converter module.

To smoothen the DC input from the adapter a 1000uF /16V electrolytic capacitor C1 is used.

Output Converter Circuits:

On the output side, two DC-DC converter modules are used to get the desired outputs (12V and 9V/5V) as per your router/modem voltage.

12V Output Port:

Buck-Boost Converter is used by considering the battery state of charge from the low voltage to fully charged condition. When the battery pack is fully charged the voltage is around 12.6V, so we have to step down (Buck Mode) the voltage to 12V. When the battery voltage is low the voltage will be less than 11V, so we have to step up the voltage (Boost Mode) to 12V.

At the same time, the DC adapter is also connected to the input of the Buck-Boost Converter, so any voltage fluctuation at the input side will be not reflected in the output.

9V/5V Output Port:

Buck Converter is used to step down the voltage from the DC adapter as well as the battery pack.

Output Capacitors:

The two 1000uF/16V electrolytic capacitors (C2 and C3) are connected at the output sides of the converter modules to avoid voltage spikes during the transition state. It will avoid the chances of rebooting during the switching between the DC adapter and battery pack.

Battery Voltage Status:

The voltmeter display is used to display the battery voltage level. The use of a rocker switch in the voltmeter circuit is to save unnecessary power wastage. You can turn it on when you want to check the battery voltage only.

Protection Fuse:

Fuse is used to provide protection against the over the current and short circuit. The fuse location is suitably selected so that it will come in both charging and discharging paths.

Disclaimer: Please note that you are working on a Li-Ion battery which is potentially very hazardous. I cannot be held responsible for any loss of property, damage, or loss of life if it comes to that. This tutorial is written for those who have ample knowledge of rechargeable lithium-ion technology. Please do not attempt this if you are a novice. Stay Safe.

Note:I have attached two schematics ( Rev-1 and Rev-2 ). The updated schematic is Rev-2 that I make after publishing my YouTube video tutorial. The changes are made by taking feedback from the users.

Before connecting the cells in parallel, first, check the individual cell voltages. For paralleling the cells, the voltage of each cell should be close to each other, otherwise, a high amount of current will flow from the cell with a higher voltage to the cell with a lower voltage. This can damage the cells and even result in fire on rare occasions.

If you are using brand new cells, the cell voltage is near 3.5 V to 3.7 V, you can join them together without worrying much. But if you are going to use an old laptop battery, be sure the cell's voltage is nearly the same, otherwise, charge the cells to the same voltage level by using a good Li-Ion Battery Charger. I used my Nitecore SC4 Charger to charge all the 18650 cells before joining them together.

To prevent short between the terminals of the batteries I have used self-adhesive insulating rings on the positive terminal side. It is not mandatory but will additional protection.

You can read this article to know why these insulator rings are so important in making a battery pack.

We have to assemble the battery to get the desired voltage and capacity. In our case, the voltage requirement is 12V and 9V / 5V.

The voltage level of a fully charged 18650 battery is 4.2V, to get 12V we have to connect 3 batteries in series (3S). To increase the capacity we have to add such series groups (3S) in parallel. Here I have used two such groups. So our final battery pack configuration is 3S2P.

If you need more backup time, add more parallel groups. In that case, the configuration will be 3S3P, 3S4P, 3S5P... and so on.

Number of batteries required to achieve 3S2P configuration = 3 x 2 = 6

Now we have to arrange the 6 batteries properly for making the electrical connection between them and with the BMS board.

Place the first parallel group of cells (2 nos) positive side up, then place the second parallel group negative side up, and finally the last parallel group positive side up. For better understanding, you can see the above picture.

I used plastic 18650 cell holders/spacers to assemble the 6 batteries. The main advantages of using these holders are:

1.You can make a custom pack of any size according to your requirement. It's like solving a puzzle.

2. It provides space between the cells, which allows fresh air to pass and the battery gets cooled easily.

3. It makes your battery pack solid and reliable.

4. It provides safety anti-vibration to your battery pack

Lay your nickel strip on top of the 2 cells ensuring that it covers the cell terminals, and then cut it. Connect the first parallel group negative terminal to the positive terminal of the second group and then the negative terminal of the second group to the positive terminal of the third group. Then spot weld the nickel strips by using a spot welder.

Here I have used a handy spot welder from SEQURE.

The spot welder can be used to weld the pure nickel as well as nickel-plated steel strips. You have to adjust the welder pulse according to the thickness of the nickel strips.

Connect the BMS as shown in the wiring diagram. The BMS has four soldering pads: B-, B1, B2, and B+. You have to connect the first parallel group negative terminal bus to the B- and positive terminal bus to the B1. Likewise the third parallel group negative terminal bus to the B2 and positive terminal bus to the B+.

You can spot weld the nickel strips to the BMS or solder them to the PCB pad. I preferred to solder the nickel strips to the PCB for a sturdy connection. First, apply soldering flux to the PCB pads and end of the nickel strips. After that tin all the pads by applying a small amount of solder and then solder them together. After spot welding, you can check the battery pack voltage to ensure you have done it correctly.

I have designed an enclosure for this project by using Autodesk Fusion 360. The dimensions of all the components are measured by a vernier caliper then the same were considered during the design.

The enclosure has two parts:

1.Main body

2. Cover lid

The Main Body is basically designed to fit all the components including the battery. The Cover lid is to cover up the main body opening.

I have used my Creality CR-10 Mini 3D printer and 1.75 mm Silver and Red PLA filaments to print the parts. It took me about 12 hours to print the main body and around 3 hours to print the top lid.